Most estimating errors come from rushed takeoffs that nobody checks twice. We verify every membrane, insulation run, and sealant quantity against your drawings and specifications before delivery, so your numbers actually hold up on site. That means fewer surprises during installation, sharper bids, and a budget that reflects the true cost of the envelope.
A slow estimate can cost you the bid before you ever submit it. Our estimators deliver detailed Division 07 takeoffs within 24 to 48 hours for most projects, so you always have reliable numbers when the clock is running. You stay ahead of every bid date and never let a good opportunity slip through the cracks.
Splitting waterproofing, insulation, roofing, and firestopping across different estimators wastes time and leaves gaps. We handle every Division 07 scope under one roof, so your building envelope estimate stays consistent and complete, from below-grade waterproofing tied to your concrete foundations to the finished roofline. That gives you one accountable partner and a single, coordinated set of numbers
Batt and roll insulation covers a large share of any envelope, and small measuring errors add up fast. We calculate exact square footage by cavity, wall, and ceiling, matched to the correct R-value, so you order the right amount of fiberglass or mineral wool without paying for waste.
From below-grade foundations to plaza decks and rooflines, waterproof membranes keep the structure safe from water intrusion. We take off every sheet and liquid-applied membrane by area, including laps, terminations, and detailing, so your bid reflects the full system and not just the flat surface.
Joints, penetrations, and control gaps all need the right sealant to stay watertight over time. We quantify caulking and protective coatings by linear foot and coverage rate, accounting for joint size and substrate, so nothing gets underestimated and your crews never run short mid-job.
Moisture rising through a slab can ruin finishes and flooring long after handover. We measure under-slab vapor barriers and floor moisture retarders by area, including overlaps and seam tape, so your slab-on-grade scope is priced accurately and protected against future callbacks.
Rigid foam board delivers continuous insulation across walls, roofs, and foundations, and every layer counts. We take off XPS, EPS, and polyiso boards by area and thickness, factoring in fasteners and coverage, so your continuous insulation quantities line up with the project energy specs.
Spray foam seals and insulates in one step, but pricing it by the wrong unit throws off the whole bid. We calculate open and closed-cell spray foam by board foot and thickness, so your quantities match the sprayed area and the R-value the assembly actually needs.
BlueTech Estimating supports contractors, developers, and design teams across every major construction sector in the United States. Whatever the project type, our thermal and moisture protection estimates are tailored to the specific costs, codes, and envelope challenges each industry brings.
We give general contractors complete, trade-by-trade Division 07 estimates, so you can bid competitively, coordinate your subcontractors, and keep the whole envelope scope on budget from start to finish.
For waterproofing, roofing, and insulation subcontractors, we prepare focused, trade-specific takeoffs that help you quote your scope accurately, protect your margins, and submit bids that win more work.
Developers and investors get clear envelope cost projections early, helping you assess feasibility, secure funding, and make confident decisions before committing to a project.
We support architects and designers with reliable Division 07 cost data during design, so your envelope details stay realistic, budget-friendly, and easier to move into construction.
Project managers rely on our detailed estimates to plan materials, track budgets, and keep timelines on course without unexpected cost surprises along the way.
Owners planning a new build or renovation get honest, easy-to-understand estimates, so you know the real cost of insulation, roofing, and waterproofing upfront and can move ahead without guesswork.
Getting started with BlueTech Estimating is simple. Have a look at the process below.
Send over your drawings and specifications, and we confirm the full Division 07 scope you need priced.
Our estimators go through every membrane, insulation run, and sealant detail so nothing in the envelope slips through.
We measure quantities and apply current material and labor pricing to prepare a clear, itemized cost estimate.
You receive a detailed, bid-ready takeoff within 24 to 48 hours, ready to submit with confidence.
Browse real samples of our takeoffs, cost estimates, and drafting work to see the level of detail you can expect on your own project.
Thermal and moisture protection estimating services calculate the materials, labor, and costs needed for a building's envelope under CSI Division 07. This covers waterproofing, insulation, vapor and air barriers, roofing, sealants, and firestopping. A detailed takeoff gives contractors accurate quantities and pricing to bid, order materials, and plan each project with confidence.
Pricing depends on the size and complexity of your project and how many Division 07 scopes you need estimated. Rather than a flat rate, we build a custom quote around your specific plans, so you only pay for the work involved. Send us your drawings, and we will give you a clear price before any work begins.
We deliver most thermal and moisture protection estimates within 24 to 48 hours. For larger or multi-scope envelope projects, we confirm a firm timeline as soon as you submit your plans. Fast turnaround means you never miss a bid deadline while waiting on your numbers.
Each estimate includes a detailed material takeoff, quantities for every envelope scope, current labor and material pricing, and a clear, itemized cost breakdown. You get numbers for waterproofing, insulation, vapor barriers, roofing, and sealants, all organized so you can bid, order materials, and manage your budget without guesswork.
Every quantity is measured directly from your drawings and specifications, then checked before delivery. We account for membrane laps, terminations, R-values, and penetrations that are easy to miss, so your estimate reflects the real scope. Accurate takeoffs mean fewer surprises on site and bids you can trust.
Getting started is simple. Send us your project plans and specifications through our contact form or email, tell us which Division 07 scopes you need, and we will review them and reply with a price and timeline. There is no obligation, and you approve everything before we begin.
CSI Division 07 covers the full building envelope, including damp-proofing and waterproofing, thermal insulation, air and vapor barriers, steep-slope and membrane roofing, wall panels and siding, sealants, and fire and smoke protection. We estimate any or all of these scopes depending on what your project and trade require.
Yes. We prepare thermal and moisture protection estimates for residential, commercial, industrial, and public sector projects of all sizes. Whether you are pricing a single-family home, a multi-family development, a hospital, or a warehouse, our estimators tailor the takeoff to the codes and cost factors of your specific project type.
Our estimators use industry-standard tools including PlanSwift, Bluebeam Revu, and On-Screen Takeoff for digital measurements, backed by current RSMeans cost data and live market pricing. This combination gives you takeoffs that are both precise and reflect what materials and labor actually cost today.
Location
815 BRAZOS ST STE 500 AUSTIN, TXCall Us
737-263-3910Mail Us
sales@bluetechestimating.comWin more bids. Control your costs. No more budget surprises.
or email us at sales@bluetechestimating.com
